DSA8300 Digital Sampling Oscilloscope
DSA8300 Digital Sampling Oscilloscope
With intrinsic jitter of less than 100 femtoseconds for extremely accurate device characterization, the DSA8300 Series provides comprehensive support for Optical Communications Standards, Time Domain Reflectometry and S-parameters. The DSA8300 Digital Sampling Oscilloscope is a complete high-speed PHY Layer testing platform for data communications from 155 Mb/sec to 400G PAM4. See all oscilloscopes »
Features |
Benefits |
Electrical module signal measurement accuracy:
|
<100 fs intrinsic jitter enables the characterization of high bit-rate (40 and 100 (4´25) Gb/s) devices with typically <5% of the signal’s unit interval being consumed by the test instrumentation. 70 GHz bandwidth allows full characterization of high bit-rate signals (5th harmonic to data rates of 28 Gb/sec and 3rd harmonic to data rates >45 Gb/sec). |
Industry’s lowest system noise at all bandwidths:
|
Minimizes the amount of instrumentation noise when acquiring high bit-rate, low-amplitude signals to eliminate additional noise which can exhibit itself as additional jitter and eye closure. |
| Up to 6 channels simultaneous acquisition at <100 fs jitter in a single mainframe. | High fidelity acquisition of multiple differential channels enables testing for cross channel impairments and improves the test throughput for systems with multiple high-speed serial channels. |
| Optical modules support optical compliance test of all standard rates from 155 Mb/s to 100 Gb/s (4x25) Ethernet. | Provides cost-effective and versatile optical test system for single and multi-mode optical standards from 155 Mb/s (OC3/STM1) to 40 Gb/s (SONET/SDH and 40GBase Ethernet) and 100 Gb/s Ethernet (100GBase-SR4, -LR4 and ER4) at 850, 1310 and 1550nm. |
| Superior acquisition throughput with up to 300 kS/s maximum sample rate. | Reduced manufacturing or device characterization test-time by 4X with superior system throughput. |
| Ability to place the samplers adjacent to the device under test (DUT). | Remote sampling heads minimize signal degradation due to cabling and fixturing from DUT to instrumentation and simplifies test system de-embed. |
| Independent calibrated channel de-skew. | Having integrated, calibrated channel deskew in dual channel modules, enhances signal fidelity for multi-channel measurements by eliminating skewing. |
Models
| Model | Analog Bandwidth | Sample Rate | Record Length | Analog Channels | List Price |
|---|---|---|---|---|---|
| DSA8300 | 70 GHz Electrical, 80 GHz Optical | Up to 300 kS/s | 50 points - 16,000 points (1M points with IConnect®, 10M points for 80SJNB) | Determined by the sampling modules used, up to 8 channels | - |
Model
DSA8300
List Price
-
Analog BandwidthSample RateRecord Length
70 GHz Electrical, 80 GHz OpticalUp to 300 kS/s50 points - 16,000 points (1M points with IConnect®, 10M points for 80SJNB)
Analog Channels
Determined by the sampling modules used, up to 8 channels
| Model | Analog Bandwidth | Sample Rate | Record Length | Analog Channels | List Price |
|---|---|---|---|---|---|
| DSA8300 | 70 GHz Electrical, 80 GHz Optical | Up to 300 kS/s | 50 points - 16,000 points (1M points with IConnect®, 10M points for 80SJNB) | Determined by the sampling modules used, up to 8 channels | - |
Model
DSA8300
List Price
-
Analog BandwidthSample RateRecord Length
70 GHz Electrical, 80 GHz OpticalUp to 300 kS/s50 points - 16,000 points (1M points with IConnect®, 10M points for 80SJNB)
Analog Channels
Determined by the sampling modules used, up to 8 channels
| Data Sheet | Software Package / Software Option | Description | Configure and Quote |
|---|---|---|---|
| 100G-SR4 | Automated Compliance and Debug Testing Solution for 100GBASE-SR4 and Transmitter and Dispersion Eye Closure (TDEC) | Contact Us | |
| 80SICMX | ICONNECT AND MEASUREXTRACTOR SIGNAL INTEGRITY AND FAILURE ANALYSIS SOFTWARE | Configure & Quote | |
| 80SICON | ICONNECT SIGNAL INTEGRITY AND FAILURE ANALYSIS SOFTWARE | Configure & Quote | |
| 80SJNB PAM4 | Comprehensive tools for PAM4 Modulation Analysis | Contact Us | |
| 80SJNB, 80SJARB | Jitter, Noise, and BER Analysis Software. | Contact Us | |
| 80SJNB01 | Jitter, Noise, and BER Analysis Advanced | Contact Us | |
| 80SJNB02 | Jitter, Noise, and BER Analysis Software with SDLA Visualizer | Contact Us | |
| 80SSPAR | ICONNECT S-PARAMETERS AND Z-LINE SOFTWARE | Configure & Quote | |
| CEI-VSR | Automated Compliance and Debug Solution for CEI-28G-VSR testing software. | Contact Us | |
| Opt. 400G-M4 | 400G Optical Manufacturing analysis software, 4 channel TDECQ | Contact Us |
| Datasheet Link | Probe | Description | Configure and Quote |
|---|---|---|---|
| DVT30-1MM GigaProbe | 30 GHz TDR probe available from GigaProbes. | Contact Us | |
| P8018 | HANDHELD TDR PROBE, PASSIVE; 20 GHZ, SINGLE-ENDED, 50 OHM, SMA CONNECTOR WITH 20 GHZ SMA CABLE; DESIGNED TO WORK WITH 80A02 EOS/ESD PROTECTION MODULE; STATEMENT OF COMPLIANCE INCLUDED WITH THIS PRODUCT | Configure & Quote | |
| P80318 | Probe kit,18GHz 100 Ohm Differential Hand Probe | Configure & Quote |
| Data Sheet | Module | Description | Configure and Quote |
|---|---|---|---|
| 80A02 | EOS/ESD PROTECTION MODULE FOR ELECTRICAL STATIC ISOLATION OF TEKTRONIX ELECTRICAL SAMPLING MODULES;STATEMENT OF COMPLIANCE INCLUDED WITH THIS PRODUCT | Configure & Quote | |
| 80C07B | OPTICAL SAMPLING MODULE; 2.488 GB/S OC48/STM16,2.500 GB/S 2GBE,2.500 GB/S INFINIBAND;2.5 GHZ OPTICAL BANDWIDTH | Configure & Quote | |
| 80C08D | Single channel optical sampling module; 10G Optical Reference Receiver Filters; 12 GHz optical bandwidth; single-/multi-mode | Configure & Quote | |
| 80C10C | Single Channel, 65/80 GHz Optical Sampling Module(must specify one of options F1, F2, or F3) | Configure & Quote | |
| 80C11B | Single channel optical sampling module; 10G Optical Reference Receiver Filters; 28 GHz optical bandwidth; single-mode | Configure & Quote | |
| 80C12B | 12 GHz, Broad WaveLength, Amplified Optical Sampling Module | Configure & Quote | |
| 80C14 | 14+ GHz, Broad WaveLength, Amplified Optical Sampling Module | Configure & Quote | |
| 80C15 | 8000 Series Optical Module: single channel, 32GHz optical bandwidth, single/multi-mode, 800nm to 1600nm | Configure & Quote | |
| 80C17 | 8000 Series Optical Module: single channel, 30GHz optical bandwidth, single/multi-mode, 800nm to 1600nm | Configure & Quote | |
| 80C18 | 8000 Series Optical Module: dual channel, 30GHz optical bandwidth, single/multi-mode, 800nm to 1600nm | Configure & Quote | |
| 80C20 | 8000 Series Optical Module: single channel, 53GHz optical bandwidth, single-mode, 1200nm to 1650nm | Configure & Quote | |
| 80C21 | 8000 Series Optical Module: dual channel, 53GHz optical bandwidth, single-mode, 1200nm to 1650nm | Configure & Quote | |
| 80E03 | SAMPLING MODULE; DUAL,20 GHZ ELECTRICAL SAMPLING MODULE - CERTIFICATE OF TRACEABLE CALIBRATION STANDARD | Configure & Quote | |
| 80E04 | SAMPLING MODULE; DUAL,20 GHZ W/TDR ELECTRICAL SAMPLING MODULE - CERTIFICATE OF TRACEABLE CALIBRATION STANDARD | Configure & Quote | |
| 80E07B | 8000 Series, Dual Channel, 30 GHz, Remote Electrical Sampling Module (includes D1) | Configure & Quote | |
| 80E08B | 8000 Series, Dual Channel, 30 GHz, Remote Electrical Sampling Module w/ TDR (includes D1) | Configure & Quote | |
| 80E09B | 8000 Series, Dual Channel, 60 GHz, Remote Electrical Sampling Module (includes D1) | Configure & Quote | |
| 80E10B | 8000 Series, Dual Channel, 50 GHz, Remote Electrical Sampling Module w/ TDR (includes D1) | Configure & Quote | |
| 80E11 | 8000 Series, Dual Channel, 70 GHz, Ultra-low Jitter, Electrical Sampling Module (includes D1) | Configure & Quote | |
| 80E11X1 | 8000 Series, Single Channel, 70 GHz, Ultra-low Jitter, Electrical Sampling Module (includes D1) | Configure & Quote | |
| 82A04B | 8000 Series, Phase Reference Module (includes D1) | Configure & Quote |
| 2019 Tektronix and Keithley Product Catalog Browse the new Tektronix and Keithley Product Catalog and explore our complete line of test and measurement solutions. You will find over 90 pages of key product details and specifications, application information, quick-reference selection guides and… | Selection Guide | 09 Sep 2019 |
| DSA8300 This document lists the warranted and typical specifications for the DSA8300 mainframe instrument as well as for the 80AXX, 80CXX, and 80EXX sampling modules. Part number: 077057100 | Performance Verification | |
| DSA8300 Supports TekScope version 6.1.X and greater. This PDF file is a printable version of the DSA8300 Series online help content. Part number: 077056901 | Online Help | |
| DSA8300 Supports TekScope version 6.2.X and greater. This PDF file is a printable version of the DSA8300 Series online help content. Part number: 077056902 | Online Help | |
| DSA8300 Digital Serial Analyzer Supports DSA8300 TekScope release 6.2.X. This document describes how to install TekScope application and other software on the DSA8300 Digital Serial Analyzer sampling oscilloscope. Part number: 071289802 | Field Install Instructions | |
| DSA8300 For DSA8300 instruments with serial number C040000 (GSA serial number B020000) and later. This document describes how to restore (rebuild) the operating system and application software on the DSA8300 Digital Serial Analyzer hard drive. Part number: 071316200 | Field Install Instructions | |
| DSA8300 Digital Serial Analyzer For DSA8300 TekScope release 6.2.1.X and greater. Instructions to install TekScope application and related software on the DSA8300 Digital Serial Analyzer sampling oscilloscope. Part number: 071289804 | Field Install Instructions | |
| DSA8300 Digital Serial Analyzer Describes how to use the Tektronix DSA8300 Digital Serial Analyzer to take 25 Gb/s measurements supporting the 802.3bm 100GBASE-KR4 backplane standard. Part number: 071320701 | Training/Tutorials | |
| DSA8300 Digital Serial Analyzer and Modules This document describes adjustments, troubleshooting, and repair procedures, including exploded views and replaceable parts lists. Part number: 077057200 | Service | |
| DSA83UP This kit provides upgrade instructions for the DSA8300 Digital Serial Analyzer instrument. The kit includes the instrument application software and documentation (as PDF files). Part number: 075103701 | Field Install Instructions | |
| DSA8300 Series, Rev A This document includes information that is necessary to clear or sanitize the DSA8300 product so it can be removed from a secured area, such as when returning the product for repair. Part number: 077057600 | Declassification | |
| DSA8300 and Sampling Modules Supports DSA8300 TekScope application 6.1.X and greater. This document lists the performance verification procedures for the DSA8300 mainframe instrument and supported optical and electrical sampling modules. Part number: 077068201 | Performance Verification | |
| DSA8300, CSA/DSA/TDS8000 Series Supports TekScope SW V6.2 (DSA8300), V5.2 (CSA/TDS/DSA8200). The Differential Channel Alignment application aligns channel acquisition and TDR step, and calibrates channel delay and TDR step deskew, for supported 80E00 series electrical sampling modules. Part number: 077077500 | Online Help | |
| DSA8300 Supports DSA8300 TekScope SW version 6.3.1.X and later. This document describes GPIB commands used to remotely control the DSA8300 Digital Serial Anayzer sampling oscilloscope. Part number: 077057003 | Programmer | |
| DSA8300 Series This manual describes the installation and operation of the DSA8300 Digital Serial Analyzer along with basic operation and concepts. Part number: 071289700 | Primary User | |
| 80X01 and 80X02 These instructions describe how to install the 80X01 (1 meter) or 80X02 (2 meter) module extender cable. For use with 80E01, 80E02, 80E03, 80E04, 80E06, 82A04B, 80E11, and 80E11X1 electrical sampling modules. Part number: 071320600 | Field Install Instructions | |
| DSA8300 Performance Verification Technical Reference This document lists the performance verification procedures for the DSA8300 mainframe instrument as well as for the 80AXX, 80CXX, and 80EXX sampling modules. Part number: 077068200 | Performance Verification | |
| DSA8300 Supports DSA8300 TekScope SW version 6.2.X and later. This document describes GPIB commands used to remotely control the DSA8300 Digital Serial Anayzer sampling oscilloscope. Part number: 077057002 | Programmer | |
| DSA8300 Digital Serial Analyzer For DSA8300 TekScope release 6.2.1.X and greater. Instructions to install TekScope application and related software on the DSA8300 Digital Serial Analyzer sampling oscilloscope. Part number: 071289803 | Field Install Instructions | |
| DSA8300 This document describes adjustments, troubleshooting, and repair procedures, including exploded views and replaceable parts lists. Part number: 077057201 | Service | |
| DSA8300 Series This document supports DSA8300 TekScope application 6.2.X. This document describes the installation and basic operation concepts of the DSA8300 Digital Serial Analyzer. Part number: 071289702 | Primary User | |
| 80A00 and 82A00 Series Supports TekScope version 6.2.x (DSA8300), 5.2.x (DSA8200). This document describes installation procedures and software compatibility information for the 80A00 and 82A00 Modules for the DSA8300 and legacy TDS/CSA/DSA8X00 series instruments. Part number: 071138613 | User | |
| DSA8300 Series This document supports DSA8300 TekScope application 6.3.X. This document describes the installation and basic operation concepts of the DSA8300 Digital Serial Analyzer. Part number: 071289703 | Primary User | |
| DSA8300 Quick Start User Manual Supports TekScope version 6.3.1.X and greater. This manual describes the installation and controls of the DSA8300 Digital Serial Analyzer, along with key operations and concepts. Part number: 071289704 | Primary User | |
| 80SJNB This document provides operating and programming instructions for the 80SJNB software application. 80SJNB provides Jitter, Noise, and BER analysis and features for de-embedding of the fixture, channel emulation, and FFE/DFE equalizer support. This version… Part number: 077064101 | Primary User | |
| DSA8300 Supports TekScope version 6.3.1.X and greater. This PDF file is a printable version of the DSA8300 Digital Serial Analyzer TekScope application help content. Part number: 077056903 | Online Help | |
| DSA8300 Supports DSA8300 TekScope SW version 6.1.X. This document describes GPIB commands used to remotely control the DSA8300 Digital Serial Anayzer sampling oscilloscope. Part number: 077057001 | Programmer | |
| DSA8300 This document describes how to restore the Microsoft Windows 7 Ultimate (32 bit) operating system software on a Tektronix DSA8300 Digital Serial Analyzer intrument. Part number: 071289900 | Field Install Instructions | |
| DSA8300 CEI-VSR This document is a PDF version of the TekExpress CEI-VSR help system. It contains installation and operatating information for product, which provides an automated, simple, and efficient way to test CEI-VSR Host to Module and Module to Host Interfaces to… Part number: 077087200 | Online Help | |
| DSA83UP This kit provides upgrade instructions for the DSA8300 Digital Serial Analyzer instrument. The kit includes the instrument application software, documentation (as PDF files), and a hard disk drive assembly if ordered with option HDD8. Part number: 075103702 | Field Install Instructions | |
| DSA8300 Series This document supports DSA8300 TekScope application 6.1.X. This document describes the installation and basic operation concepts of the DSA8300 Digital Serial Analyzer. Part number: 071289701 | Primary User | |
| DSA8300 and Sampling Modules Supports DSA8300 TekScope application 6.1.X and greater. This document lists the performance verification procedures for the DSA8300 mainframe instrument and supported optical and electrical sampling modules. Part number: 077068202 | Performance Verification | |
| DSA8300 Oscilloscope Firmware for Windows 7 V6.3.1.5 Part number: 066133310 | Firmware | |
| Serial Data Link Analysis Visualizer, DSA8300 JNB02, V2.2.0 Serial Data Link Analysis Visualizer, DSA8300 JNB02, V2.2.0 Part number: 066168400 | Application | |
| TekExpress RIN Automated Measurement Solution Software application v1.0.0 Part number: 066165900 | Application | |
| CEI-VSR - OIF CEI 3.0 Compliance Solution for DSA8300 Part number: 066161501 | Application |
| DSA8300 and 80A00, 80C00, 80E00, 80N01, 80X00, 82A00 Sampling Modules Declassification and Security
This document includes information that is necessary to clear or sanitize the DSA8300 product and related sampling modules so it can be removed from a secured area, such as when returning the product for repair. Part number: 077057604 | Declassification | |
| 2019 Tektronix and Keithley Product Catalog Browse the new Tektronix and Keithley Product Catalog and explore our complete line of test and measurement solutions. You will find over 90 pages of key product details and specifications, application information, quick-reference selection guides and… | Selection Guide | 09 Sep 2019 |
| Oscilloscope Selection Guide From basic signal-checking to high-performance analysis, this selection guide gives an overview of the complete range of oscilloscopes from Tektronix. Literature number: 46W-31080-5 | Selection Guide | 29 Aug 2019 |
| XYZs of Oscilloscopes Primer After reading this primer, you will be able to: Describe how oscilloscopes work, Describe the differences between analog, digital storage, digital phosphor, and digital sampling oscilloscopes, describe electrical waveform types, understand basic… Literature number: 03Z-8605-7 | Primer | 27 Aug 2019 |
| Equalization and Serial Data Link Analysis Methods (SDLA) with 80SJNB Advanced Application Note Describes the Equalization concept and SDLA methods using the 80SJNB. Literature number: 61W-21428-1 | Application Note | 14 Aug 2019 |
| Variations in 10 Gigabit Ethernet Laser Transmitter Testing Using Reference Receivers One of the key tools used by telecom/datacom original equipment manufacturers, system installers and system servicers to view eye patterns on an oscilloscope and test the quality of a lasers time-domain signal is the reference receiver (RR). Literature number: 85W-16691-1 | Application Note | 14 Aug 2019 |
| 5 and 6 Series MSO 12-bit Scope Yes! Tektronix offers many different models of real-time oscilloscopes that provide 12-bit or greater vertical resolution for a variety of applications. Because many high-vertical-resolution oscilloscopes on the market have technical trade-offs such as… | FAQ ID: 69266 | 29 Jul 2019 |
| DSA8300 and 80A00, 80C00, 80E00 Sampling Modules Performance Verification
Supports DSA8300 TekScope Application Software 6.3.1.x and above. This document describes the performance verification procedures for the DSA8300 Digital Serial Analyzer and supported electrical, optical, and accessory sampling modules. Part number: 077068205 Rev A | Performance Verification | |
| How do I use TekVISA to send commands to my instrument? TekVISA Download Link:TEKVISA CONNECTIVITY SOFTWARE In order to communicate with and control the scope, you can use OpenChoice Talker-Listener. Back on the Application and Utilities panel, click on OpenChoice Talker Listener and click Start Application… | FAQ ID: 69181 | 25 Jun 2019 |
| How do I use the programmer manual for my instrument? TekVISA Download Link: TEKVISA CONNECTIVITY SOFTWARE Hello and welcome to Tektronix, today I’m presenting the last part in the 3-part series on using TekVISA. I’ll be giving a basic overview of programmer manuals and how to use them to find the correct… | FAQ ID: 69186 | 25 Jun 2019 |
| DSA8300 Digital Serial Analyzer, 80C00/80E00/80A00 modules Specifications
This document lists the warranted and typical specifications for the DSA8300 Digital Serial Analyzer, 80C00 Series Optical Sampling Modules, 80E00 Series Electrical Sampling Modules, and 80A00 Modules. Part number: 077057105 | Performance Verification | |
| 100G-TXE - IEEE-802.3bj:CR4/KR4 and IEEE-802.3bm:CAUI4 Transmitter Compliance Solution for DSA8300 - V1.0.1.96 The TekExpress 100G-TXE automation test solution facilitates turnkey electrical transmitter validation of 100GBASE-CR4, 100GBASE-KR4, and CAUI-4 standards of IEEE. Part number: 066190501 | Application | |
| 400G-M4 PAM4 Optical Manufacturing TDECQ Analysis Software for Tektronix DSA8300 - V1.1.0.12 PC based analysis software package provides up to 4 channel support enabling higher throughput rates through parallel channel acquisition and processing. Features in the DSA8300 400G-M4 Analysis include:? Support for 4 channel simultaneous acquisition?… Part number: 066134770 | Application | |
| CEI-VSR - OIF CEI 3.1 Compliance Solution for DSA8300 - V1.3.1.160 The Tektronix CEI-VSR is an automated compliance solution for testing OIF CEI 3.1 Compliance Solution, which includes Host to Module (TP1a) and Module to Host (TP4)CEI-VSR Part number: 066172601 | Application | |
| Automation Answers Compliance Challenge Interoperability and compliance concerns are commanding an ever-larger share of the serial system designer's attention. Literature number: 55W-21408-0 | Fact Sheet | 25 Apr 2019 |
| 400G-TXO support IEEE 802.3bs and 802.3cd: 50GBASE-FR/LR, 100GBASE-DR, 200GBASE-DR4/ LR4/FR4 and 400GBASE-LR8/FR8/DR4 Optical Conformance and Characterization Solution for DSA8300 V 1.0.2 The 400G-TXO application package is an automated conformance and characterization solution for IEEE 802.3bs and IEEE 802.3cd specifications. This package operates on DSA8300 sampling instrument with 80C10C optical module. The 80S400G-TXO offers a… Part number: 066191901 | Application | |
| TekExpress RIN Automated Measurement Solution Software Application - V1.1.2 TekExpress RIN provides an automated, simple, and efficient way to take RIN (Relative Intensity Noise) and RINxOMA (Optical Modulation Amplitude) measurements on optical signals.-RIN and RINxOMA measurements can be performed on PRBS7, PRBS9,PRBS11, PRBS13… Part number: 066181602 | Application | |
| 100GBASE-SR4 and TDEC Measurement Solution for DSA8300 - V1.1.2 The TekExpress 100GBASE-SR4 / TDEC Automated Measurement Solution provides turnkey testing and characterization of Tx Optical properties key to the SR4 Short Reach EthernetSpecifications outlined in IEEE 802.3bm. Part number: 066179403 | Application | |
| 80SJNB, 80SJARB, SDLA Visualizer and Scope Noise Characterization Application Software Release - V4.5.9.0, V4.0.4.0, V2.2.0.4, V 1.0.0.64 80SJNB, 80SJARB, SDLA Visualizer, and Scope Noise Characterization software run on the DSA8300 instruments with Windows 7 Operating System. This release of 80SJNB adds updates to TDECQ measurements in support of 100 ? 400 Gbps, PAM4 signal analysis, with… Part number: 066134713 | Application | |
| NRZ-M4 Optical Manufacturing TDEC Analysis Software for Tektronix DSA8300 - V1.1.0.37 Tektronix NRZ-M4 is a PC based application which offers optical NRZ signaling analysis, including TDEC(Transmitter and Dispersion Eye Closure) measurement. The application brings together NRZ optical measurements in a simple and easy to use application.… Part number: 066199900 | Application |